Experimental study on combustion stability and performance of hydrogen-enriched compressed natural gas of a free-piston linear generator

Free Piston linear Generator (FPLG) engine fueled by compressed natural gas (CNG) has recently gained increased research attention. However, due to the low-velocity burning and poor lean limit of CNG fuel, the FPLG engine combustion stability, performance, and efficiency are still low. Hydrogen has a greater burning velocity with wider flame limits that could extend the lean burn limits and combustion characteristics of CNG. This paper compares pure CNG and 10% hydrogen-enriched CNG at various ignition speeds (0.6 ms, 0.8 m/s, and 1 m/s), injection positions (0 mm, 5 mm, 10 mm and 15 mm), and lambda ratios (0.9, 1.4 and 1.7) on the combustion characteristics, performance, and conversion efficiency are duly discussed. The findings show that the FPLG combustion stability limits increase with the hydrogen addition into the CNG. The CNG in-cylinder pressure increases significantly when the injection position is advanced, whereas the hydrogen addition reduces the influence of the injection position. The heat release rate increases by 15.62% and 23.72% with hydrogen addition, corresponding to the advanced and retarded injection positions. Consequently, the hydrogen addition increases the power RMS to 209.21 W and 232.64 W with an increment of 3.46% and 3.13%, respectively. Conclusively, the hydrogen addition into the CNG evidently shortens the combustion duration while improving the heat release rate, combustion stability, power RMS, Cycle-to-Cycle variation, and conversion efficiency.     

Validation of a 3D multiphase-multicomponent CFD model for accidental liquid and gaseous hydrogen releases

As hydrogen-air mixtures are flammable in a wide range of concentrations and the minimum ignition energy is low compared to hydrocarbon fuels, the safe handling of hydrogen is of utmost importance. Additional hazards may arise with the accidental spill of liquid hydrogen. Such a release of LH2 leads to a formation of a cryogenic pool, a dynamic vaporization process, and consequently a dispersion of gaseous hydrogen into the environment. Several LH2 release experiments as well as modeling approaches address this phenomenology. In contrast to existing approaches a new CFD model capable of simulating liquid and gaseous distribution was developed at Forschungszentrum Jülich. It is validated against existing experiments and yields no substantial lacks in the physical model and reveals a qualitatively consistent prediction. Nevertheless, the deviation between experiment and simulation raises questions on the completeness of the database, in particular with regard to the boundary conditions and available measurements.     

镜面杂质与水汽吸放对露点仪影响的实验研究

显微成像露点仪在研制和测试过程中发现镜面杂质和内腔材质吸放水汽等影响测量精度的问题。针对镜面杂质对显微成像露点仪测量的影响开展了镜面图像特征的实验研究，结果表明：镜面杂质点处露珠凝结具有优先性，且反复凝结消散后镜面出现杂质沉降现象。针对水汽吸放对显微成像露点仪的影响开展了水汽释放与吸附效应的实验研究，结果表明：当温度发生变化时，显微成像露点仪感应舱内壁氧化铝材质存在释放（或吸附）水汽现象，使得显微成像露点仪测量值偏大（或偏小）。研究结果为露点仪在功能设置及镜面与腔体材料选择方面提供了参考。     

泳池式轻水反应堆内电磁线圈可控温辐照装置设计

本文设计了在泳池式轻水反应堆（简称泳池堆）内在线测量电磁线圈电性能的可控温辐照装置。采用MCNP程序进行中子物理计算，对泳池堆、线圈骨架的结构尺寸与物质组分进行了精细全尺寸模拟，得出辐照装置的发热功率和中子注量率。通过初步估算，使用ANSYS CFX进行了数值模拟，得出辐照装置内线圈在堆运行时的温度，并提出温度控制的方法。辐照装置采用铝材加工制造，并进行了垂直度测试、气压测试、检漏测试。增加了绝缘设计，将辐照装置与泳池堆之间进行绝缘。在线圈处预埋铠装热电偶，对线圈温度进行实时监测。在泳池堆内对电磁线圈进行辐照试验，结果表明，本文设计的辐照装置能满足电磁线圈在泳池堆孔道内进行辐照试验的要求，并可对电磁线圈进行实时温度控制。     

Incorporation of calcium salts into xanthan gum matrices: hydration,erosion and drug release characteristics

Xanthan gum (XG), a hydrophilic biopolymer with modified release properties, was used to produce directly compressed matrix tablets containing a model drug, sodium p-aminosalicylate. Three formulations were prepared, each containing a different calcium dihydrate salt: calcium chloride, calcium sulfate or dibasic calcium phosphate. The aim of the investigation was to relate the calcium ion content and solubility of the calcium salt to the in vitro drug release profile of the xanthan matrices. Tablet hydration, erosion and drug release were determined in distilled water using the British Pharmacopoeia (BP) paddle method. The data showed that the overall drug release was the greatest with addition of calcium sulfate, followed by calcium chloride and dibasic calcium phosphate. The chloride salt formulation displayed the greatest percentage erosion due to rapid mass loss during the initial phase, followed by those with sulfate or phosphate salts. As xanthan gel viscosity increased and drug release was also found to be lower, it can be concluded that drug release is influenced by the solubility of the salt present in the formulation, since these parameters determine the viscosity and structure of the gel layer.     

Long-term sustained-released in situ gels of a water-insoluble drug amphotericin B for mycotic arthritis intra-articular administration: preparation,in vitro and in vivo evaluation

Amphotericin B (AMB) was often used in intra-articular injection administration for fungal arthritis, because it could often bring a satisfactory therapeutic efficacy and a minimum systemic toxic side effect. However, because of the multiple operations and the frequent injections, the compliance of the patients was bad. Therefore, to develop a long-term sustained-released preparation of AMB for mycotic arthritis intra-articular administration is of great significance. The purpose of present study was to develop a long-term sustained-released in situ gel of a water-insoluble drug AMB for mycotic arthritis intra-articular administration. Based on the evaluations of the in vitro properties of the formulations, the formulation containing 10% (w/w) ethanol, 15% (w/w) PG, 0.75% (w/w) HA, 5% (w/w) purified soybean oil, 0.03% (w/w) α-tocopherol, 15% (w/w) water and 55% (w/w) glyceryl monooleate was selected as a suitable intra-articular injectable in situ gel drug delivery system for water-insoluble drug AMB. Furthermore, the results of the in vivo study on rabbits showed that the selected formulation was a safe and effective long-term sustained-released intra-articular injectable AMB preparation. Therefore, the presented in situ AMB gel could reduce the frequency of the administration in the AMB treatment of fungal arthritis, and then would get a good patient compliance.     

Application of chitosan–alginate microspheres for the sustained release of bacteriophage in simulated gastrointestinal conditions

This study was designed to evaluate the acid stability, release property and antimicrobial efficacy of Escherichia coli O157:H7 bacteriophages encapsulated in chitosan–alginate microspheres under the simulated gastrointestinal conditions. The bacteriophages belonging to Myoviridae family were stable at the pH above 4 in trypticase soy broth. The chitosan–alginate microspheres exhibited protective effect on the viability of bacteriophages in the simulated gastric conditions at pH 2.0 and pH 2.5, showing 4.8 and 5.6 log PFU mL^‐1, respectively, after 1 h of incubation at 37 °C. The release per cent of bacteriophages from microspheres gradually increased up to 65% in the simulated intestinal condition (pH 7.5) at 37 °C for 6 h. The lytic efficacy of chitosan‐ and alginate‐encapsulated bacteriophages against E. coli O157:H7 was significantly maintained in the simulated intestinal conditions to 10 h of incubation (1.3 log reduction). The results suggest that the chitosan–alginate microspheres can be used as a reliable delivery system for bacteriophages.     

Carbonaceous microsphere-based superabsorbent polymer as filler for coating of NPK fertilizer: Fabrication,properties, swelling,and nitrogen release characteristics

Recently, the use of controlled release fertilizers in agriculture has resulted in huge benefits in plant growth and cultivation. Superabsorbent polymer (SAP)-coated fertilizers have the added advantage in retaining water in soil after irrigation and also reduce the nutrient release rate from soil in a controlled manner. This study aimed to produce a nitrogen–phosphorus–potassium (NPK) fertilizer coated with superabsorbent carbonaceous microspheres polymer (SPC) by inverse suspension polymerization method with water-retention and controlled release properties. Two sets of experiments were conducted: (1) three different weight percentages and (2) different materials. NPK coated with SPC showed increasing water-retention ability with respect to carbon microsphere percentages and retains >80% water at the 30th day of experiment compared with pure NPK and NPK coated with SAP. The slow release behavior of all samples was investigated by induced coupled plasma mass spectrometry spectrometry and results showed that NPK coated with SAP and SPC has a low release rate with <50% nutrient release compared with uncoated NPK at the 30th day. The release mechanism kinetics of NPK coated with SAP and SPC were studied based on the Kosmeyer–Peppas model. The mechanisms approached Fickian diffusion-controlled release as the n value for both samples was less than 0.5. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48396.     

In vivo evaluation of a mucoadhesive polymeric caplet for intravaginal anti-HIV-1 delivery and development of a molecular mechanistic model for thermochemical characterization

Context and objective: The aim of this study was to develop, characterize and evaluate a mucoadhesive caplet resulting from a polymeric blend (polymeric caplet) for intravaginal anti-HIV-1 delivery.

Materials and methods: Poly(lactic-co-glycolic) acid, ethylcellulose, poly(vinylalcohol), polyacrylic acid and modified polyamide 6, 10 polymers were blended and compressed to a caplet-shaped device, with and without two model drugs 3′-azido-3′-deoxythymidine (AZT) and polystyrene sulfonate (PSS). Thermal analysis, infrared spectroscopy and microscopic analysis were carried out on the caplets employing temperature-modulated DSC (TMDSC), Fourier transform infra-red (FTIR) spectrometer and scanning electron microscope, respectively. In vitro and in vivo drug release analyses as well as the histopathological toxicity studies were carried out on the drug-loaded caplets. Furthermore, molecular mechanics (MM) simulations were carried out on the drug-loaded caplets to corroborate the experimental findings.

Results and discussion: There was a big deviation between the T_g of the polymeric caplet from the T_g's of the constituent polymers indicating a strong interaction between constituent polymers. FTIR spectroscopy confirmed the presence of specific ionic and non-ionic interactions within the caplet. A controlled near zero-order drug release was obtained for AZT (20 d) and PSS (28 d). In vivo results, i.e. the drug concentration in plasma ranged between 0.012–0.332?mg/mL and 0.009–0.256?mg/mL for AZT and PSS over 1–28 d.

Conclusion: The obtained results, which were corroborated by MM simulations, attested that the developed system has the potential for effective delivery of anti-HIV-agents.